Thursdays with Sandiebella

It’s THURSDAY with Sandiebella!

Hiya sistahs, happy Thursday with Sandiebella !

Today Sandiebella teaches us how to make a Triple Tier Slider Card

 

Supplies:
Card
Papers (used –  Carta Bella)
Scoring board and bone folder
Pencil, ruler, eraser
Dies used – Postage Stamp, Pierced Oval, Pierced Rectangle.
How to:

Stamp Thanksgiving Oddball onto blending card, colour and fussy cut around the outline. Use a craft knife to cut pieces the pieces the scissors can’t reach. Set aside to work on the card.

Cut:
White card:
Tiers: 4.5″ x 11-3/8″, 3-1/8″ x 10.25″, and 3″ x 3″
Paper:
Large tier:  4-3/8″ x 3.75″
Middle tier: 3.25″ x 3″
Small tier: 2-7/8″ x 2-7/8″
Slider mechanisms (x2): 0.5″ x 4″
Score the 4.5″ x 11-3/8″ piece at 3-7/8″ and 7.75″

Score the 3-1/8″ x 10.25″ piece at 3-3/8″ and 6.75″

Fold in the right side on the score line, then fold the left side on top. Crease well with a bone folder.

Open out the card pieces. On the inside right section of the larger piece, measure in 1″ from the 7.75″ score line, and the outside edge. At the 1″ marks, measure down 0.75″ from the top and draw a line down to 3.5″

On the smaller piece, repeat the step above, measuring in 1″ from the score line and outside edge, but measure down from the top and draw a line from 0.25″ to 2.5″

Use a craft knife to cut each side of the lines, making slits approx. 1/16″ wide.

Fold up the pieces again and adhere the paper layers to the front of all three layers

Take the two 0.5″ x 4″ pieces of paper

Slide the pieces through the slits

Fold around the card between the slits, not too tightly, and glue the ends together to make the sliding mechanisms. Push the sliding mechanism of the middle tier down to the bottom and apply adhesive to it.

Take the smallest tier and centre it horizontally, adhering it so that approx 1/8″ protrudes at the top.

Apply adhesive to the inside of the left side, fold in the right side, and then fold the left side down on top of it.

Repeat the sliding mechanism steps with the large tier, adhering the middle tier to the mechanism but keeping the top flush with the top of the large tier.

Fold up the  large tier to complete the card base.

Create a front panel using a postage stamp and rectangle die.

Stamp the sentiment onto white card and cut out with an oval die. While the die is still in place ink with Antique Linen distress oxide ink.

Adhere both Thanksgiving Oddball and the sentiment oval to the front panel using foam tape/dots.

Punch a 1.5″ circle from designer paper. Fold in half and cut across the crease line.

Adhere the half circles each side of the top tier to create a pull tab.

Decorate the tiers, adding a place to write a personal message on the middle tier. A gift card can be added to the top tier.

Share your personal favourite Stamping Bella creations with us. We LOVE to see what you’ve been creating with Stamping Bella stamps. Share a link to your latest Stamping Bella card in the comments below, or an old favourite you made a while ago. Tell us what your favourite stamps are. Are there any additions you would like to see to the range? Let us know!

Another way to connect is by joining us in the Stamping Bella Sistahood Facebook Group and share your pictures.

If you are posting your images online, we would love to see them on Instagram and all the platforms mentioned above. To make it easier for us to find you just use #stampingbella as a hashtag. Even better tag me @stampingbella . We love it when you connect, so don’t be shy!

Until next time, HAPPY STAMPING!

MWAH

One Comment

  1. Nancee Purdum says:

    Awesome! Thanks for sharing!

Leave a Reply

Comments (required)