GIFT CERTIFICATE!

Treat someone special to a Stamping Bella

Click to continue

Thursday with Sandiebella: Create a Surprise Double Wiper Card

Sandie has a fab tutorial for us again this week!

Surprise Double Wiper Card

 

Supplies:

Designer paper
Scoring board and bone folder
Ruler and pencil
Embellishments

How to: 

Stamp Edna the Everything Fairy onto a piece of blending card.
Using the masking technique, stamp three of the cupcakes onto a piece of card measuring 1 7/8″ x 1 7/8″.
Stamp a single cupcake onto a separate piece of card.
Stamp the sentiment from Edna with a Cupcake on Top, onto a 1 7/8″ x 1 7/8″ piece of card.

Colour the images using your preferred medium and set aside to make the card base.

To make the wiper mechanism cut one piece of card measuring 2 3/8″ x 6″ (6cm x 15.2cm)
Score at 1 1/8″, 4.25″, and 5.5″ (2.7cm, 10.7cm, and 13.7cm)

Make a notch at  3 1/8″ (7.7cm), top and bottom

Score diagonally from the top 3 1/8″ notch down to the 5.5″ (13.7cm) score line. Repeat from the bottom 3 1/8″ notch up to the 5.5″ (13.7cm) score line

Mountain fold both end score lines and the diagonal score lines. Valley fold the 4.25″ (10.7cm) line.

For the card base: 
Cut one piece of card measuring 5 1/8″ x 10.25″ (13cm x 26cm). Score at 5 1/8″ (6.5cm) on the long side. Fold and crease the score line.

Inside panels:
Cut two pieces of card measuring 5″ x 5″ (12.8cm x 12.8cm) and two pieces of paper measuring 4 7/8″ x 4 7/8″ (12.4cm x 12.4cm)
Cut one piece of card measuring 5″ x 3 3/8″ (12.8cm x 8.6cm) and one piece of paper measuring 4 7/8″ x 3.25″ (12.4cm x 8.2cm )
Adhere the paper to each of the card panels.
Wipers:
Cut 2 pieces of card measuring 2 1/8″ x 2 1/8″ (5.4cm x 5.4cm)
Cut two pieces of paper measuring 2″ x 2″ (5cm x 5cm)

Adhere the two larger panels to the inside of the card base.

On the inside back panel, mark 3 1/8″ (8cm) from the score line centered vertically 2 3/8″ (6.5cm)

Make a pencil mark in the centre of the wiper mechanism at the 5.5″ (13.7cm) score line.

Apply adhesive to the outside of the smaller end and, folding it under and lining up the pencil marks, adhere it down.

Apply adhesive to the outside of other end of the mechanism. Fold the flap under and, keeping it flat, adhere to the inside front of the card base.

Once the glue has dried, fold over the card base and use a bone folder to smooth the score lines on the wiper mechanism.

Open the card up and apply adhesive to bottom triangle as shown.

Adhere one of the 2 1/8″ x 2 1/8″ (5.4cm x 5.4cm) pieces of card to it.

Repeat for the top wiper, adhering the paper layers and the images too.

Apply adhesive to the large section of the wiper mechanism as shown.

Adhere the 5″ x 3 3/8″ (12.8cm x 8.6cm) panel, burnishing well with a bone folder
For the card front:

Cut one piece of card measuring 4/78″ x 4 7/8″ (12.4cm x 12.4cm) and a selection of papers to decorate as preferred.

Fussy cut around Edna and the single cupcake. Adhere both to the card front using foam tape/dots, placing the cupcake in Edna’s hand.
Stamp the sentiment from Edna the Everything Fairy onto a strip of card and cut to size. Adhere to the card front and embellish as desired.

Over To You!

Share your personal favourite Stamping Bella creations with us. We LOVE to see what you’ve been creating with Stamping Bella stamps. Share a link to your latest Stamping Bella card in the comments below, or an old favourite you made a while ago. Tell us what your favourite stamps are. Are there any additions you would like to see to the range? Let us know!

Another way to connect is by joining us in the Stamping Bella Sistahood Facebook Group and share your pictures.

If you are posting your images online, we would love to see them on Instagram and all the platforms mentioned above. To make it easier for us to find you just use #stampingbella as a hashtag. Even better tag me @markergeek and Emily @stampingbella . We love it when you connect, so don’t be shy!

Until next time, HAPPY STAMPING!

MWAH

Elaineabella

Post navigation

2 comments

Leave a comment

Your email address will not be published. Required fields are marked *